Ferris wheel thread

[Tom C]

I am hoping that a resistance mismatch is all that is needed between the coils.

Tom C

[min2oly]

Hi Ron,
I'd love the PDF.
I can resize and upload for everyone min2oly@yahoo.com
Thanks

I think JB's post was for those (John K.) who might be having a go at sizing "down" to get started. I also think it was intended for 36 volts??? He did say at the time it will be difficult to size down and get the same effects, he also said he would have liked to make his BIGGER! ouch :-)

KR,
Patrick A.

[ATTACH=CONFIG]3706[/ATTACH]Patrick,

Here's an incomplete schematic that shows the Bedini/Cole switch as used on the Ferris Wheel. Its set up for 36V input.

Ron

Sorry this picture is not good when viewed on the forum. I have it in pdf if you need it.

Ron

[Ron Chase]

Patrick,

Here's an incomplete schematic that shows the Bedini/Cole switch as used on the Ferris Wheel. Its set up for 36V input.

Ron

Sorry this picture is not good when viewed on the forum. I have it in pdf if you need it.

Ron

[min2oly]

Hi John K. and/or Tom,
If you are reading this, can you add any content to this post of John Bedini's here:

"John K,
I would use that coil for the side coils. and wind another by putting two of the bobbins together double the impedance in Ohms 14. And make sure you put the shield on the bottom then run the Bedini/Cole circuit. The capacitor should be about 18000Uf use a SCR and a 4.7volt Zener with two 2.8 volt super bright Leds in series with the diode circuit. Machine RPM should be not more then 25 Rpm's. just giving you a tip. Good Work

John B"

Did you ever get 3 coils on that wheel? I'm curious if you think his intention was that you go all the way to 36v input?

I think when I finish all 3 of my coils, I might be close to 1 ohm total and even 12 volts might be too much potential and the mjl21194 might heat up.
John mentions that the highly modified ckt will limit the current and the coils can do their work so I'll just keep plodding along...
Thanks for any help... suggestions.
KR,
Patrick A.

[Tom C]

even in his absence he is causing strife... no more about the dude, it was not about what he was sharing, but what he refused to do. back to building and sharing. I will delete any more posts about him, his email is above go do what he does wherever he is, but for peace sake let's move on.

Tom C

[Dave Wing]

Yo Stevie aka erfinder,

Thanks for the MS Word messages embedded in your URL - what gives here?

erfinder@forgotten-genius.com

As an aside, I did enjoy the "erfinder dissect"thread, along with its truly interesting information and unique take on reality -great video. Unfortunately, all of it attracted too much negative attention which resulted in the abysmal lock down. Your accommodating style and philosophy is perhaps too foreign for most western readers, "c'est la vie"!

Your current situation brings to mind the trials and tribulations of the ***anese Zen master Bankei whose matured wisdom is displayed in the book "The Unborn". I point you in that direction...

Thank you for your contributions,
Yaro

Yaro,

Do you honestly think Steve is or was having issues here, on this forum because he is or was misunderstood or his concepts were or are to far advanced for us uneducated, unsofisticated westerners? Lets be real... Here.

Plainly his choice of select words, in communication got him into trouble... Nothing else!

-Dave Wing

[Yaro1776]

Yo Stevie aka erfinder,

Thanks for the MS Word messages embedded in your URL - what gives here?

erfinder@forgotten-genius.com

As an aside, I did enjoy the "erfinder dissect"thread, along with its truly interesting information and unique take on reality -great video. Unfortunately, all of it attracted too much negative attention which resulted in the abysmal lock down. Your accommodating style and philosophy is perhaps too foreign for most western readers, "c'est la vie"!

Your current situation brings to mind the trials and tribulations of the ***anese Zen master Bankei whose matured wisdom is displayed in the book "The Unborn". I point you in that direction...

Thank you for your contributions,
Yaro

[Tom C]

Took a few moments over the last few days to wind the second coil. One more to go etc...
[ATTACH=CONFIG]3668[/ATTACH]

messing around w/ coil placement, thought I'd give a wave as we go along...
[ATTACH=CONFIG]3669[/ATTACH]

KR
Patrick A.

Very nice Patrick!!

Tom C

[Tom C]

run along then, off you go!

Tom C

[erfinder]

My own forum...good idea Tom....the best advice you have given to date. Thanks for the email plug.....just in case anyone wants to reach out to me...


erfinder@forgotten-genius.com


@admin

I request you delete my account.

[Tom C]

I locked the thread because it was descending into chaos, and I will not put up with it, from anyone. radiant was obnoxious in some of his posts and so was ortho and others. steve calling those who are John's friends names does not win awards for anyone, and I do not need to justify myself to anyone, your posts are all the evidence needed to lock it.

[erfinder]

Have you asked to have it unlocked? I would like it to become unlocked as well... Admin what needs to be done to unlock that thread?

-Dave Wing

this post was off topic to the thread

[Dave Wing]

Have you asked to have it unlocked? I would like it to become unlocked as well... Admin what needs to be done to unlock that thread?

-Dave Wing

[erfinder]

Ok... In what thread would you do this?

Dave Wing

post off topic to this thread

[Dave Wing]

Nope........not in this thread...

Ok... In what thread would you do this?

Dave Wing